Lab Consumables
Gloves, glassware, PPE · 25 items · independent inventory.
Premium316L Stainless Cut-Wire Shot 0.5 mm
Cold-cut 316L stainless cut-wire shot, 0.5 mm cylindrical. Premium media for copper-alloy parts — brass, bronze and precision electronic components — leaves no corrosion residue.
Aluminium-safeLow-Hardness Steel Shot S230 (Aluminium-Casting Use)
Ultra-low-carbon soft-quenched shot, 0.6 mm, HRC 35–40. The soft hardness avoids deformation on aluminium and magnesium-alloy thin-wall parts during de-scaling.
Low-Bainite Hardened Steel Shot S390
Isothermally-quenched bainite steel shot, 1.2 mm, HRC 55–60. Lower fragmentation rate vs. conventional S-shot — for high-strength gears, crankshafts and wind-power / aerospace peening.
Wear-resistantHigh-Chrome Alloy Cast Steel Shot S330
High-chrome alloy steel shot (Cr 8–12%), 1.0 mm, HRC 58–62, alloyed-and-quenched. Extreme wear resistance — significantly reduces media consumption rate in high-volume blasting lines.
410 Stainless Steel Shot 1.0 mm
Atomised 410 martensitic stainless shot, 1.0 mm, HRC 35–40. Harder than 304 — for peening and strengthening of stainless castings, knives, moulds and wear parts.
304 Stainless Steel Shot 0.8 mm
Atomised 304 stainless shot, 0.8 mm, HRC 25–30. For stainless valves, fittings, precision instruments and decorative surface finishing.
No rust304 Stainless Steel Shot 0.5 mm
Atomised 304 stainless (0Cr18Ni9) shot, 0.5 mm, HRC 25–30, spherical. Non-ferrous-contaminating blast media — no rust spotting on the workpiece. For medical devices, food machinery and aerospace.
Cut-Wire Shot CW1.5
Cut-wire shot from 70# high-carbon wire, 1.5 mm cylindrical, HRC 45–50. Coarse-format cut wire for heavy cast-steel parts, marine, wind-power and construction-machinery peening.
Cut-Wire Shot CW1.2
Cut-wire shot from 70# high-carbon wire, 1.2 mm cylindrical, HRC 45–50. Heavier cycle life than equivalent S-shot. Used for surface strengthening on gears, bearings and springs.
Long lifeCut-Wire Shot CW1.0
Cut-wire shot from 70# high-carbon wire, 1.0 mm cylindrical particles, HRC 45–50. Cold-cut + polished. Long service life for repeated-cycle blasting on cast parts and long-term steel descaling.
Cast Steel Grit G50 (Angular)
Crushed and heat-treated high-carbon steel grit, 2.0 mm, HRC 55–60. Largest-size angular grit — for super-heavy structures, mining equipment and large ships.
Cast Steel Grit G40 (Angular)
Crushed and heat-treated high-carbon steel grit, 1.5 mm, HRC 55–60. For heavy structural-steel descaling, bridge work and wind-power tower preparation.
Cast Steel Grit G25 (Angular)
Crushed and heat-treated high-carbon steel grit, 1.2 mm, HRC 55–60. Large-format angular grit for ship steel plates, large castings and heavy-machinery surface prep.
Cast Steel Grit G18 (Angular)
Crushed and heat-treated high-carbon steel grit, 1.0 mm, HRC 55–60. Heavy-clean angular grit for cast iron, cast steel and construction-machinery castings.
Cast Steel Grit G16 (Angular)
Crushed and heat-treated high-carbon steel grit, 0.8 mm, HRC 55–60. General-service angular grit for automotive parts and structural steel pre-treatment.
Cast Steel Grit G14 (Angular)
Crushed and heat-treated high-carbon steel grit, 0.6 mm, HRC 55–60. Standard angular grit for valve, pump and small-component descaling and roughness control.
Sharp profileCast Steel Grit G12 (Angular)
Crushed and heat-treated high-carbon steel grit, 0.4 mm, HRC 55–60, angular. Sharp-edged particle profile for precise descaling on precision castings, stainless steel and aluminium-alloy components.
Cast Steel Shot S550 (High Carbon)
High-carbon atomised steel shot, 2.0 mm, HRC 50–55. The heaviest size in our peening range — for oversized cast-steel parts, mining-machinery castings and heavy steel structures.
Cast Steel Shot S460 (High Carbon)
High-carbon atomised steel shot, 1.5 mm, HRC 50–55. Heavy-grade peening shot for cast steel parts, marine structures and wind-power hubs.
PeeningCast Steel Shot S390 (High Carbon)
High-carbon atomised steel shot, 1.2 mm, HRC 50–55. Strengthened formulation (C 0.6–0.8%) for shot-peening service — extends fatigue life on gears, springs and shafts.
Cast Steel Shot S330 (Low Carbon)
Low-carbon atomised steel shot, 1.0 mm, HRC 40–45. Heavy-duty size for large cast-iron parts, heavy-machinery castings and bridge structural-steel pre-treatment.
Cast Steel Shot S280 (Low Carbon)
Low-carbon atomised steel shot, 0.8 mm, HRC 40–45. Standard size for automotive chassis castings, containers and general foundry shot-blasting lines.
Cast Steel Shot S230 (Low Carbon)
Low-carbon atomised steel shot, 0.6 mm, HRC 40–45. Workhorse size for cast-iron parts, forgings and structural steel — de-scaling and cleaning.
Top sellerCast Steel Shot S170 (Low Carbon)
Low-carbon atomised steel shot, 0.5 mm, HRC 40–45. General-purpose shot for de-rusting and surface preparation of small-to-medium castings, hardware and stampings.
Fine cleanCast Steel Shot S110 (Low Carbon)
Low-carbon atomised steel shot, 0.3 mm, HRC 40–45, SAE-standard. Atomised and quench-hardened from low-C steel for fine-cleaning service. The smallest size in our low-carbon range — ideal for thin-wall and precision castings.